74ACT163M ,SYNCHRONOUS PRESETTABLE 4-BIT COUNTERABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
74ACT163MTC ,Synchronous Presettable Binary Counter74AC163 • 74ACT163 Synchronous Presettable Binary CounterNovember 1988Revised February 200074AC163 ..
74ACT163PC ,Synchronous Presettable Binary Counter74AC163 • 74ACT163 Synchronous Presettable Binary CounterNovember 1988Revised February 200074AC163 ..
74ACT163SCX ,Synchronous Presettable Binary CounterFunctional DescriptionThe AC/ACT163 counts in modulo-16 binary sequence.From state 15 (HHHH) it inc ..
74ACT163SJ ,Synchronous Presettable Binary CounterFunctional DescriptionThe AC/ACT163 counts in modulo-16 binary sequence.From state 15 (HHHH) it inc ..
74ACT163SJX ,Synchronous Presettable Binary CounterFunctional DescriptionThe AC/ACT163 counts in modulo-16 binary sequence.From state 15 (HHHH) it inc ..
74HC174D ,Hex D-type flip-flop with reset; positive-edge triggerLogic diagram74HC_HCT174 All information provided in this document is subject to legal disclaimers. ..
74HC174N ,Hex D-type flip-flop with reset; positive-edge triggerPin configuration DIP16 Fig 5.
74HC174PW ,Hex D-type flip-flop with reset; positive-edge triggerINTEGRATED CIRCUITSDATA SHEETFor a complete data sheet, please also download:• The IC06 74HC/HCT/HC ..
74HC175D ,Quad D-type flip-flop with reset; positive-edge triggerINTEGRATED CIRCUITSDATA SHEETFor a complete data sheet, please also download:• The IC06 74HC/HCT/HC ..
74HC175DB ,Quad D-type flip-flop with reset; positive-edge triggerGENERAL DESCRIPTIONcorresponding output (Q ) of the flip-flop.nThe 74HC/HCT175 are high-speed Si-ga ..
74HC175N ,Quad D-type flip-flop with reset; positive-edge triggerFeatures and benefits Input levels: For 74HC175: CMOS level For 74HCT175: TTL level Four edge-t ..
74ACT16374DLR
16-Bit D-Type Edge-Triggered Flip-Flops With 3-State Outputs
Flow-Through Architecture OptimizesPCB Layout Distributed Center-Pin VCC and GND
Configurations Minimize High-Speed
Switching Noise EPIC (Enhanced-Performance Implanted
CMOS) 1- m Process 500-mA Typical Latch-Up Immunity at
125°C Package Options Include Plastic 300-mil
Shrink Small-Outline (DL) Packages Using
25-mil Center-to-Center Pin Spacings and
380-mil Fine-Pitch Ceramic Flat (WD)
Packages Using 25-mil Center-to-Center
Pin Spacings
descriptionThe SN54ACT16374 and 74ACT16374 are 16-bit
edge-triggered D-type flip-flops with 3-state
outputs designed specifically for driving
highly-capacitive or relatively low-impedance
loads. They are particularly suitable for
implementing buffer registers, I/O ports,
bidirectional bus drivers, and working registers.
These devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock
(CLK) input, the Q outputs of the flip-flop take on the logic levels set up at the data (D) inputs.
An output-enable input (OE) can be used to place the outputs in either a normal logic state (high or low logic
levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines
significantly. The high-impedance state provides the capability to drive bus lines in a bus-organized system
without need for interface or pullup components. OE does not affect the internal operations of the flip-flop. Old
data can be retained or new data can be entered while the outputs are in the high-impedance state.
The 74ACT16374 is packaged in TI’s shrink small-outline package, which provides twice the I/O pin count and
functionality of standard small-outline packages in the same printed-circuit board area.
The SN54ACT16374 is characterized for operation over the full military temperature range of –55°C to 125°C.
The 74ACT16374 is characterized for operation from –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1Q1
1Q2
GND
1Q3
1Q4
VCC
1Q5
1Q6
GND
1Q7
1Q8
2Q1
2Q2
GND
2Q3
2Q4
VCC
2Q5
2Q6
GND
2Q7
2Q8
2OE
1D1
1D2
GND
1D3
1D4
VCC
1D5
1D6
GND
1D7
1D8
2D1
2D2
GND
2D3
2D4
VCC
2D5
2D6
GND
2D7
2D8
2CLK