DS9097U-009# ,Universal 1-Wire COM Port Adapter DS9097U Universal 1-Wire COM Port Adapter
DS9097U-E25 ,Universal 1-Wire COM Port AdapterDS9097U®Universal 1-Wire COM Port Adapterwww.dalsemi.com
DS9098P-TRL ,iButton RetainerDS9098PiButton Retainer www.dalsemi.com19.30
DS90C031BTM ,LVDS Quad CMOS Differential Line Driverapplications requiring ultra low power dissipa- n High impedance LVDS outputs with power-offtion an ..
DS90C031BTMX ,LVDS Quad CMOS Differential Line DriverFeatures>n 155.5 Mbps (77.7 MHz) switching ratesThe DS90C031B is a quad CMOS differential line driv ..
DS90C031BTMX ,LVDS Quad CMOS Differential Line Driverapplications.Connection Diagram Functional DiagramDual-In-Line10098901Order Number DS90C031BTMSee N ..
DS9097U-009#
Universal 1-Wire COM Port Adapter
AVAILABLE
FEATURES
True-Ground Interface to an RS-232 COM Port for Reading and Writing 1-Wire® Devices
Works with Bipolar as well as Unipolar Logic Signals
Compatible to COM port of (±)5V to (±)12V (DB9 Version Only) or (±)6V to (±)12V (DB25 Version)
Supports Reading and Writing at Standard and Overdrive Speeds
Provides Strong Pullup to 5V for Temperature and EEPROM 1-Wire Devices
Programs 1-Wire EPROM Devices (DB-25 Version with External 12V Power Supply Only)
Communicates at Data Rates of 9.6kbps (default), 19.2kbps, 57.6kbps, and 115.2kbps
Standard DB9 or DB25 Female Connector and 6-Lead RJ11 Connector for Easy Attachment of Standard 1-Wire Cables and Probes
Includes DS2502 Identification Chip (DS9097U-009 Only) PIN ASSIGNMENT
DB9: TXD (3), RXD (2), DTR (4), RTS (7), PC-Ground (5); all other pins not connected
DB25: TXD (2), RXD (3), DTR (20), RTS (4), PC-Ground (7); all other pins not connected
Note 1: The external supply for the DS9097U-E25 must provide well-regulated 12V at 10mA minimum, center = GND, outer ring = V+ (Newark Electronics Stock No. 84F2081, Allied Electronics Stock No. 928-9895, Stancor Model STA-300R, or equivalent).
Note 2: The color of the DS9097U plastic case can vary.
ORDERING INFORMATION
PART TYPE DS9097U-009# DB9, with DS2502 ID chip DS9097U-S09# DB9, no ID chip DS9097U-E25# DB25, with EPROM write #Denotes a RoHS-compliant device that may include lead(Pb) that is exempt under the RoHS requirements.
PACKAGE OUTLINE
DB9 VERSION SIDE VIEW REAR VIEW
RJ11 PIN 1
DB25 VERSION RJ11 PIN 1
SIDE VIEW REAR VIEW
+ CONTACT
- CONTACT
2.1mm POWER JACK
SCHEMATIC (FOR ILLUSTRATION)
DB9 VERSION 4
RTS DTR RXD TXD GND
RS-232 COM PORT 5V REG DS2480B
RJ11
1-W GND 5 4 3 2 1
ID CHIP
DS9097U-009 ONLY
DB25 VERSION 4
RTS DTR RXD TXD GND
RS-232 COM PORT
5V REG DS2480B
RJ-11
1-W GND 5 4 3 2 1
POWER JACK
9V
DS9097U Universal 1-Wire COM Port Adapter 1-Wire is a registered trademark of Maxim Integrated Products, Inc.
DS9097U
DESCRIPTION The DS9097U is a sophisticated RS-232 to 1-Wire adapter, which performs RS-232 level conversion and actively generates the 1-Wire communication signals. Together with an adequate software driver, it enables a Windows®-based PC to directly communicate with any 1-Wire device connected to the adapter’s RJ11 port. The DB9 version reads and writes any non-EPROM 1-Wire device. To write to EPROM devices, the DB25 version with external power supply is required. For a list of suitable 1-Wire network cables, refer to the Connectivity Matrix table in the DS1402x 1-Wire network cables data sheet. All DS9097U adapters are based on the DS2480B serial 1-Wire line driver chip. The RXD/TXD polarity select input of the DS2480B is connected to VDD (noninverting). Free software drivers can be /1-Wiredrivers. The DS9097U communicates with 1-Wire devices at standard speed as well as overdrive speed. The serial port must support a data transmission rate of 9600bps. Under software control, the adapter can be set up for RS-232 data rates of 19200bps, 57600bps, and 115200bps. The two higher rates are recommended for communication at overdrive speed with overdrive-capable devices. Since the DS9097U operates in a byte mode, every data byte received from the RS-232 port generates eight time slots on the 1-Wire line. Note that there are some COM ports that use signal levels of less than (±) 5V. The DB9 versions of this adapter do not work with such ports. The DS9097U-E25 adapter, however, functions in most cases if external power is supplied. Without EPROM programming, the external power can be anywhere in the range of 6V to 9V. For EPROM programming the voltage must be at 12V in any case. Before using an externally powered DS9097U-E25 with a COM port of less than (±) 5V, check whether the COM port will not be damaged by 5V on its RXD input.
Windows is a registered trademark of Microsoft Corp.
DS9097U
REVISION HISTORY REVISION DATE DESCRIPTION PAGES CHANGED 9/00 Initial release —
2/04 Updated for change in plastic body style; added note that the color of the plastic body may vary 1
8/09 Added the # sign to all the part numbers in the Ordering Information table; added the Revision History table 1, 3
6/11 Deleted references to Crypto devices, TMEX, DS9097, and DS9097E; added reference to the Connectivity Matrix table in the DS1402x 1-Wire network cables data sheet; updated the URL for software drivers download 1, 2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
