STSR2CD-TR ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERSTSR2FORWARD SYNCHRONOUSRECTIFIERS SMART DRIVER■ SUPPLY VOLTAGE RANGE: 4.5V TO 5.5V■ TYPICAL PEAK O ..
STSR2P ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
STSR2PCD ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV DC Input Voltage-0.3 to 6 VCCV Max Gate Drive ..
STSR2PMCD ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERSTSR2P/STSR2PMFORWARD SYNCHRONOUSRECTIFIERS SMART DRIVER■ SUPPLY VOLTAGE RANGE: 4.5V TO 5.5V■ TYPIC ..
STSR2PMCD ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERapplications with logic gateCCthreshold mosfets. UVLO feature guarantees proper start-up while it a ..
STSR2PMCD-TR ,FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVERSTSR2P/STSR2PMFORWARD SYNCHRONOUSRECTIFIERS SMART DRIVER■ SUPPLY VOLTAGE RANGE: 4.5V TO 5.5V■ TYPIC ..
T5743P3 ,UHF ASK/FSK ReceiverBlock Diagram UHF ASK/FSKUHF ASK/FSKRemote control transmitter Remote control receiverT5743U2741BDe ..
T5743P3 ,UHF ASK/FSK ReceiverFeatures• Two Different IF Receiving Bandwidth Versions Are Available (B = 300 kHz or 600 kHz)IF• 5 ..
T5743P3-TGQ ,UHF ASK/FSK Receiverapplications are in the areas of telemetering, security technology and keyless-entrysystems. It can ..
T5744 ,UHF ASK Receiver ICFeatures• Minimal External Circuitry Requirements, no RF Components on the PC Board Except Matching ..
T5750 ,UHF ASK/FSK TransmitterFeatures• Integrated PLL Loop Filter ESD Protection also at ANT1/ANT2 (4 kV HBM/200 V MM; Except P ..
T5750 ,UHF ASK/FSK TransmitterBlock Diagram UHF ASK/FSK UHF ASK/FSKRemote control transmitter Remote control receiver1 Li cellT5 ..
STSR2CD-STSR2CD-TR
FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVER
1/11October 2002 SUPPLY VOLTAGE RANGE: 4.5V TO 5.5V TYPICAL PEAK OUTPUT CURRENT:
SOURCE -2A, SINK 3.5A OPERATING FREQUENCY:20 TO 750 KHZ SMART TURN-OFF ANTICIPATION TIMING OPERATION INDEPENDENT FROM THE
FORWARD MAGNETIC RESET TECHNIQUE POSSIBILITY TO OPERATEIN
DISCONTINUOUS MODE
DESCRIPTIONSTSR2 Smart Driver IC provides two
complementary high current outputs to drive
Power Mosfets. TheICis dedicatedto properly
drive secondary Synchronous Rectifiers in
medium power, low output voltage, high efficiency
Forward Converters. Froma synchronizing clock
input, STSR2 generates two driving signals with
the self-setting of dead time between
complementary pulses. TheIC operation prevents
secondary side shoot-through conditions
providing proper timingat the outputs turn-off
transition. This smart function operates througha
fast cycle-after-cycle control logic mechanism
based on an internal high frequency oscillator,
synchronized by the clock signal. A fixed
anticipation in turning-off the OUT GATE1 with
respectto the clock signal transitionis provided,
while the anticipationin turning off the OUT GATE2can be set through external components. The
adopted transitions revelation mechanism makes
circuit operation independent by the forward
magnetic reset technique used, avoiding mostof
the common problems inherent in self-driven
synchronous rectifiers.A special Inhibit function
allows the shut-offof OUTGATE2. This feature
makes discontinuous conduction mode possible
and prevents the freewheeling mosfet from
sinking current from the output.
STSR2 automatically turns off the outputs when
duty-cycleis lower than 13%, while STSR2M
works evenat very low duty-cycle values.
STSR2FORWARD SYNCHRONOUS
RECTIFIERS SMART DRIVER
SCHEMATIC DIAGRAM
STSR22/11
ABSOLUTE MAXIMUM RATINGSAbsoluteMaximum Ratingsare those values beyond which damagetothe device may occur. Functional operation under these conditionis
not implied.
(*)A higher positive voltage level canbe appliedtothepin witha resistor which limitsthe current flowingintothepinto 10mA maximum
THERMAL DATA(*) This valueis referredtoone layerpcb board with minimum copper connectionsforthe leads.a minimum valueof 120 °C/Wcanbe
obtained improving thermal conductivityofthe board
ORDERING CODES
CONNECTION DIAGRAM (top view)
STSR23/11
PIN DESCRIPTION
STSR24/11
ELECTRICAL CHARACTERISTICS(VCC =5V, CK= 250kHz,V INHIBIT =-200mV,TJ =-40to 125°C, unless
otherwise specified.)
Note1:tRis measured between 10% and 90%ofthe final voltage;tFis measurerd between 90% and 10%onthe initiualvoltage
Note2: Parameter guaranteedby design
STSR25/11
TIMING DIAGRAM
APPLICATION INFORMATION: STSR2IN FORWARD CONVERTER SECONDARY SIDENOTES Ceramic CapacitorsC1andC2 mustbe placed very closetotheIC;R1 andR2set theanticipationtimeby partitioning theVcc voltage;R3andR4isa resistor divider meantto providethe correctCk voltage range;R5 limitsthe current flowing through diodeD2 when Freewheeling drain voltageis high;D1 couldbe necessaryto protect INHIBITpin from negative voltages.D2 couldbe necessaryto protect INHIBITpin from voltages higher thanVccD3 couldbe necessaryto protectCKpin from voltages higher than Vcc. SGLGND layout trace mustnot include OUTGATE1,2 current paths.A capacitorin parallel withR4 couldbe necessaryto eliminate turnoff voltage spike.
STSR26/11
EXAMPLE OF COMPONENTS SELECTION FORA FORWARD CONVERTERForward Specification:IN =36-72V
VOUT=3.3V
n=Np/Ns=4.53 andR4 are calculated assuringa minimum voltageof 2.8Vat Ck pin.At 36V input, the voltageon the
secondary windingis 36/4.5=8V. Choosing R3=1.5KΩ,R4 resultsto be:
R4=1kΩis chosen.At 72V input the currentatCk pinis calculated as:
This valueis below the maximum allowable current flowing into the Ck pin (10mA).If the 10mA valueis
exceededan external diode connectedtoVCC mustbe added (D3). and R2 values set the anticipation time for OUTGATE2.For R1=∞ and R2=0, tANT2=75ns; for
R1=R2=10kΩ,tANT2=150ns;for R1=0 and R2=∞,tANT2=225ns.
The RC group composed byR5 and the parasitic capacitanceof Inhibit pin (typically 5pF) delays the
signal on Inhibit comparator. This delay mustbe lower than 200ns. This condition imposesa maximum
value forR5of about 20kΩ. generala suggested value forR5is 10kΩ.At 72V input, the secondary voltageis 16V,so the maximum
current flowing into Inhibit pinis 16V/10kΩ=1.6mA whichis below the maximum allowable currentfor the
pin (10mA).If the 10mA valueis exceededan external diode (D2) connectedto VCC mustbe added.
The maximum negative voltageof –0.6V mustbe guaranteed for the Inhibit pin.If this negative voltageis
exceeded the current mustbe limitedto 50mA.If necessary,a diode (D1) connectedto SGLGND canbe
addedto satisfy this specification.
INHIBIT OPERATION OF OUTGATE2IN DISCONTINUOUS CONDUCTION MODE4CKICK 2.8() R3×+INICK2.8()– R3 VCK–×--------------- --------------- --------------- -------------------≥ 1kΩ 2.8V 220μA1.5kΩ×+ 220μA– 1.5kΩ 2.8V–×--------------- --------------- --------------- ---------------- -------------× 965Ω==CKIN max() VCC– 0.3–3
--------- --------------- --------------- -------------- 16 5– 0.3–
1.5kΩ------------------------------ 7.13mA== =