IGW75N60T ,1200V IGBT for frequencies up to 10kHz for hard switching applications and up to 30kHz for soft switching. Combined Trench- and Fieldstop-Technology. ...applications offers : - very tight parameter distribution P-TO-247-3-1 (TO-220AC) - high ruggedn ..
IH401A ,QUAD Varafet Analog Switchapplications of JFETs required the addition ofISSdiodes, in series with the gate, and then perhaps ..
IH5009CPD ,Virtual Ground Analog SwitchIH5009-5012, 5014,5016-5020, 5022, 5024May 1999Virtual Ground Analog Switch
IH5010CPD ,4-channel; 30V; 10mA; 500mW; virtual ground analog switchIH5009-5012, 5014,5016-5020, 5022, 5024May 1999Virtual Ground Analog Switch
IH5010MDD ,4-channel; 30V; 10mA; 500mW; virtual ground analog switchIH5009-5012, 5014,5016-5020, 5022, 5024May 1999Virtual Ground Analog Switch
IH5010-MDD ,4-channel; 30V; 10mA; 500mW; virtual ground analog switchapplications. Although low cost is aIntegrated Logicprimary design objective, performance and versa ..
IR3Y30M1 , CCD Signal Processors for B/W CCD Cameras
IR3Y30M1 , CCD Signal Processors for B/W CCD Cameras
IR4007K , Switched Mode Power Supply IC
IR4426 ,Dual Low Side Driver, Inverting Input in a 8-pin DIP package Data Sheet No. PD60177 Rev. FIR4426/IR4427/IR4428(S) & (PbF)DUAL LOW SIDE DRIVER
IR4426PBF ,Dual Low Side Driver, Inverting Input in a 8-pin DIP packageElectrical CharacteristicsV (V ) = 15V, T = 25°C unless otherwise specified. The V , and I paramete ..
IR4426S ,Dual Low Side Driver, Inverting Input in a 8-lead SOIC packageElectrical CharacteristicsV (V ) = 15V, T = 25°C unless otherwise specified. The V , and I paramete ..
IGW75N60T
1200V IGBT for frequencies up to 10kHz for hard switching applications and up to 30kHz for soft switching. Combined Trench- and Fieldstop-Technology. ...
IGW75N60T TrenchStop Series q Low Loss IGBT in Trench and Fieldstop technology Very low VCE(sat) 1.5 V (typ.) Maximum Junction Temperature 175 °C Short circuit withstand time – 5µs
• Designed for : - Frequency Converters - Uninterrupted Power Supply Trench and Fieldstop technology for 600 V applications offers : - very tight parameter distribution - high ruggedness, temperature stable behavior - very high switching speed - low VCE(sat) Positive temperature coefficient in VCE(sat)
• Low EMI Low Gate Charge Complete product spectrum and PSpice Models : http://www.infineon.com/igbt/
Maximum Ratings V µs W
°C
IGW75N60T TrenchStop Series q
Thermal Resistance
Characteristic
Electrical Characteristic, at Tj = 25 °C, unless otherwise specified
Static Characteristic
Dynamic Characteristic
IGW75N60T TrenchStop Series q
Switching Characteristic, Inductive Load, at Tj=25 °C
IGBT Characteristic
Switching Characteristic, Inductive Load, at Tj=175 °C
IGBT Characteristic 1) Includes Reverse Recovery Losses from IKW75N60T due to dynamic test circuit in Figure E.
IGW75N60T TrenchStop Series q R CU
10Hz100Hz1kHz10kHz100kHz
50A
00A
50A
200A
R CU10V100V1000V
10A
100Af, SWITCHING FREQUENCY VCE, COLLECTOR-EMITTER VOLTAGE
Figure 1. Collector current as a function of
switching frequency (Tj ≤ 175°C, D = 0.5, VCE = 400V,
VGE = 0/+15V, RG = 5Ω)
Figure 2. Safe operating area (D = 0, TC = 25°C, Tj ≤175°C;
VGE=15V)
t,
R D
SSI
25°C50°C75°C100°C125°C150°C0W
50W
100W
150W
200W
250W
300W
350W
400W
R CU
25°C75°C125°C0A
30A
60A
90A
120ATC, CASE TEMPERATURE TC, CASE TEMPERATURE
Figure 3. Power dissipation as a function of
case temperature (Tj ≤ 175°C)
Figure 4. DC Collector current as a function
of case temperature (VGE ≥ 15V, Tj ≤ 175°C)
IGW75N60T TrenchStop Series q COL
CUR1V2V3V
30A
60A
90A
120A
COL
CUR1V2V3V
30A
60A
90A
120AVCE, COLLECTOR-EMITTER VOLTAGE VCE, COLLECTOR-EMITTER VOLTAGE
Figure 5. Typical output characteristic
(Tj = 25°C)
Figure 6. Typical output characteristic
(Tj = 175°C)
COL
CUR2V4V6V8V0A
20A
40A
60A
80A
(sat),
COL
T S
AGE
0°C50°C100°C150°C0.0V
0.5V
1.0V
1.5V
2.0V
2.5VVGE, GATE-EMITTER VOLTAGE TJ, JUNCTION TEMPERATURE
Figure 7. Typical transfer characteristic (VCE=20V) Figure 8. Typical collector-emitter saturation voltage as a function of
junction temperature
(VGE = 15V)
IGW75N60T TrenchStop Series q CHIN
TIME40A80A120A10ns
100ns
CHIN
TIME10Ω15Ω
10ns
100nsIC, COLLECTOR CURRENT RG, GATE RESISTOR
Figure 9. Typical switching times as a
function of collector current
(inductive load, TJ=175°C,
VCE = 400V, VGE = 0/15V, RG = 5Ω,
Dynamic test circuit in Figure E)
Figure 10. Typical switching times as a
function of gate resistor
(inductive load, TJ = 175°C,
VCE= 400V, VGE = 0/15V, IC = 75A,
Dynamic test circuit in Figure E)
CHIN
TIME
25°C50°C75°C100°C125°C150°C
100ns
(th
),
GAT
TRS
VO
AGE
-50°C0°C50°C100°C150°C0VTJ, JUNCTION TEMPERATURE TJ, JUNCTION TEMPERATURE
Figure 11. Typical switching times as a function of junction temperature
(inductive load, VCE = 400V,
VGE = 0/15V, IC = 75A, RG=5Ω,
Dynamic test circuit in Figure E)
Figure 12. Gate-emitter threshold voltage as a function of junction temperature
(IC = 1.2mA)
