SN74CBTH16211DL ,24-Bit FET Bus Switch With Bus Hold SN74CBTH16211 24-BIT FET BUS SWITCHWITH BUS HOLDSCDS062C – JUNE 1998 – REVISED NOVEMBER 2001DGG, D ..
SN74CBTK16245DGGR ,16-Bit FET Bus Switch With Active-Clamp Undershoot Protection Circuit
SN74CBTK32245GKER , 32 BIT FET BUS SWITCH WITH ACTIVE CLAMP UNDERSHOOT PROTECTION CIRCUIT
SN74CBTLV16210 ,Low-Voltage 20-Bit FET Bus Switchmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74CBTLV16210DL ,Low-Voltage 20-Bit FET Bus Switch SCDS042J − DECEMBER 1997 − REVISED JULY 2004DGV OR DL P ..
SN74CBTLV16210GR ,Low-Voltage 20-Bit FET Bus Switchmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74S38 ,Quad 2-input positive-NAND buffers with open collector outputs
SN74S38 ,Quad 2-input positive-NAND buffers with open collector outputs
SN74S38 ,Quad 2-input positive-NAND buffers with open collector outputs
SN74S38 ,Quad 2-input positive-NAND buffers with open collector outputs
SN74S38DR ,Quad 2-input positive-NAND buffers with open collector outputs
SN74S482N ,4-Bit-Slice Expandable Control Elements 20-PDIP 0 to 70
SN74CBTH16211DL
24-Bit FET Bus Switch With Bus Hold
descriptionThe SN74CBTH16211 provides 24 bits of
high-speed TTL-compatible bus switching. The
low on-state resistance of the switch allows
connections to be made with minimal propagation
delay.
The device is organized as dual 12-bit bus
switches with separate output-enable (OE)
inputs. It can be used as two 12-bit bus switches
or one 24-bit bus switch. When OE is low, the
associated 12-bit bus switch is on, and the A port
is connected to the B port. When OE is high, the
switch is open, and a high-impedance state exists
between the two ports.
Active bus-hold circuitry is provided to hold
unused or floating A and B ports at a valid logic
level.
To ensure the high-impedance state during power
up or power down, OE should be tied to VCC
through a pullup resistor; the minimum value of
the resistor is determined by the current-sinking
capability of the driver.
ORDERING INFORMATION Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1A2
1A3
1A4
1A5
1A6
GND
1A7
1A8
1A9
1A10
1A11
1A12
2A1
2A2
VCC
2A3
GND
2A4
2A5
2A6
2A7
2A8
2A9
2A10
2A11
2A12
1B1
1B2
1B3
1B4
1B5
GND
1B6
1B7
1B8
1B9
1B10
1B11
1B12
2B1
2B2
2B3
GND
2B4
2B5
2B6
2B7
2B8
2B9
2B10
2B11
2B12
NC – No internal connection
