IC Phoenix logo

Home ›  G  › G3 > GBJ1508

GBJ1508 from RRD

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

GBJ1508

Manufacturer: RRD, LITEON, LT

Voltage 50V ~ 1000V 15.0 Amp Glass Passivited Bridge Rectifiers

Partnumber Manufacturer Quantity Availability
GBJ1508 RRD, LITEON, LT 431 In Stock

Description and Introduction

Voltage 50V ~ 1000V 15.0 Amp Glass Passivited Bridge Rectifiers The part GBJ1508 is a bridge rectifier manufactured by LITEON. Here are its key specifications:

- **Type**: Single-Phase Bridge Rectifier
- **Maximum Average Forward Current (Io)**: 15A
- **Peak Forward Surge Current (Ifsm)**: 150A
- **Maximum Reverse Voltage (Vr)**: 800V
- **Forward Voltage Drop (Vf)**: 1.1V (typical) at 7.5A
- **Operating Temperature Range**: -55°C to +150°C
- **Package**: GBJ (GBJ-4), through-hole mounting
- **Mounting Type**: Through Hole
- **Diode Configuration**: Single-Phase Bridge

These specifications are based on standard conditions unless otherwise noted. For detailed performance characteristics, refer to the official LITEON datasheet.

Application Scenarios & Design Considerations

Voltage 50V ~ 1000V 15.0 Amp Glass Passivited Bridge Rectifiers# GBJ1508 Technical Documentation

## 1. Application Scenarios

### Typical Use Cases
The GBJ1508 is a bridge rectifier module commonly employed in AC-to-DC conversion circuits where space constraints and thermal management are critical considerations. Typical applications include:

 Power Supply Units 
- Switching mode power supplies (SMPS) for consumer electronics
- Linear power supplies for industrial control systems
- Battery charger circuits for automotive and portable devices

 Motor Control Systems 
- DC motor drives in industrial automation
- Servo motor controllers in robotics
- HVAC system motor control circuits

 Lighting Applications 
- LED driver circuits for commercial lighting
- High-intensity discharge (HID) lamp ballasts
- Emergency lighting power conversion

### Industry Applications
 Industrial Automation 
- PLC power supply sections
- Sensor interface power circuits
- Control panel power distribution

 Consumer Electronics 
- Television and monitor power boards
- Audio amplifier power stages
- Home appliance control circuits

 Automotive Electronics 
- On-board charger systems
- Power window motor controllers
- Automotive lighting systems

 Renewable Energy 
- Solar charge controller circuits
- Wind turbine power conversion
- Battery management systems

### Practical Advantages and Limitations

 Advantages: 
-  Compact Design : Integrated bridge configuration reduces PCB footprint by approximately 60% compared to discrete diode solutions
-  Thermal Performance : Metal casing provides efficient heat dissipation, supporting continuous operation at elevated temperatures
-  High Reliability : Industrial-grade construction ensures stable performance in harsh environments
-  Simplified Assembly : Single-component installation reduces manufacturing complexity and improves production yield

 Limitations: 
-  Fixed Configuration : Cannot be reconfigured for different rectifier topologies
-  Thermal Constraints : Maximum junction temperature of 150°C requires adequate heatsinking for high-current applications
-  Voltage Drop : Typical forward voltage of 1.1V per diode leg results in higher power dissipation compared to Schottky alternatives
-  Frequency Limitations : Not suitable for high-frequency switching applications above 20kHz

## 2. Design Considerations

### Common Design Pitfalls and Solutions

 Thermal Management Issues 
-  Pitfall : Inadequate heatsinking leading to thermal runaway and premature failure
-  Solution : Implement proper thermal calculations and use heatsinks with thermal resistance ≤ 2.5°C/W for full-load operation

 Voltage Spikes 
-  Pitfall : Unsuppressed voltage transients causing avalanche breakdown
-  Solution : Incorporate snubber circuits and TVS diodes for overvoltage protection

 Current Imbalance 
-  Pitfall : Uneven current sharing in parallel configurations
-  Solution : Use current-balancing resistors (0.1-0.5Ω) and ensure symmetrical PCB layout

### Compatibility Issues

 With Capacitive Loads 
- High inrush currents may exceed device ratings
- Implement soft-start circuits or NTC thermistors

 With Inductive Loads 
- Voltage spikes during switching transitions
- Use freewheeling diodes and RC snubber networks

 With Microcontrollers 
- Ensure proper grounding to avoid noise coupling
- Maintain minimum 10mm clearance from sensitive analog circuits

### PCB Layout Recommendations

 Thermal Management 
- Use thermal vias under the package for improved heat transfer to ground planes
- Maintain minimum 3mm clearance from other heat-generating components
- Provide adequate copper area (≥ 100mm²) for heatsinking

 Electrical Considerations 
- Place input filter capacitors within 10mm of AC input pins
- Route high-current traces with minimum 2oz copper thickness
- Implement star grounding for noise-sensitive applications

 Mechanical Considerations 
- Ensure proper mounting hole clearance for mechanical stability
- Allow for thermal expansion in high-temperature applications
- Use conformal coating in humid or corrosive environments

## 3. Technical Specifications

### Key

Alternative Part Number

  • KBJ1508 --: Same 15A 800V bridge rectifier in an equivalent KBJ package, widely available and a direct functional drop-in.
  • GBU1508 --: 15A 800V glass-passivated bridge rectifier with comparable ratings; GBU package may require minor lead forming but is electrically equivalent.
  • DF1508M --: 15A 800V bridge rectifier offering similar forward current and reverse voltage; check package footprint compatibility before substitution.
  • DF1508S --: 15A 800V bridge rectifier in a different package style; electrically equivalent and usable where board layout allows package adaptation.
  • TS15P08G --: 15A 800V bridge rectifier with similar electrical characteristics, suitable as a functional replacement.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips